How to do Longboard Cleaning and maintain it for a longer time for the best experience?
If you are anything like me, you probably love your longboard. It is a beautiful piece of equipment that allows for exciting adventures with friends and family. However, maintaining it can be a bit tricky at times – especially if you don’t know how to clean it properly!
To help make this process easier for both beginners and experts alike, we have put together 11 steps on how to extend the life of your longboard thorough cleaning and maintenance.
What's in it?
- Step One: Cleaning Your Board with a Brush!
- Step Two: Cleaning Your Board with a Soap and Water!
- Step Three: Using a Nylon Brush to Clean the Surface!
- Step Four: Longboard Cleaning Permanently Mounted Bearings!
- Step Five: Cleaning Your Non-Permanently Mounted Bearings!
- Step Six: Rinsing Your Longboard Off!
- Step Seven: Keeping your Longboard Clean!
- Step Eight: Storage!
- Step Nine: Learning to Maintain Your Board!
- Step Ten: Extra Tips!
- Step 11: Buy a good quality longboard!
Step One: Cleaning Your Board with a Brush!
Brushing your longboard for maintenance after each use can remove dirt and debris that may have accumulated during the ride. The brush bristles will help you get in all of those hard-to-reach places to keep them free from grime.
It’s also best to avoid trying to clean the surface if it is too wet, so wait for it to dry before brushing off any excess water or snow! Use a soft-bristle paintbrush (avoid metal) for this task because they are gentler on wood surfaces than stiffer brushes.
You can find these at most hardware stores – just make sure you buy one that has natural or nylon bristles rather than metal ones which might damage your longboard.
Step Two: Cleaning Your Board with a Soap and Water!
Sometimes, dirt can be too embedded in the surface of your board to brush off with just a brush alone – especially if you are out on rides that take place over many days or weeks. Use soap and water for these stubborn stains by gently rubbing it into those areas using circular motions before rinsing them away completely!
We recommend using dish soap for this task because it is milder than most other soaps which will help to prevent damage from build-up over time (especially important when dealing with wood surfaces).
Keep some scrubbing sponges nearby as well – they make great tools for getting right up against corners where debris may have gathered without doing any damage.
Step Three: Using a Nylon Brush to Clean the Surface!
If you want to clean your longboard even more thoroughly, consider using a nylon brush (again, avoid metal as much as possible) on its surface. These can be found in most hardware stores as well and are perfect for removing any stubborn debris that may remain after brushing with soap and water or basic scrubbing sponges!
Be sure not to use this type of brush too aggressively – it will do more damage than good if you press down too hard when applying pressure. Gentle circular motions work best so take your time while cleaning off all grime from those tricky corners by the bolts where dirt likes to accumulate over time.
This is also an excellent way of removing scuffs or scratches from the surface of your board if you have had any unfortunate accidents.
Step Four: Longboard Cleaning Permanently Mounted Bearings!
If you are unsure about how to clean these, it may be best to consult an expert because they can simply take them out and wash those for you!
But before that happens, there is a trick that will help decrease some of the build-up over time (especially when riding in salty conditions). Take a damp cloth and apply rubbing alcohol on its surface – this should help dissolve some dirt particles so that they don’t stick around as much.
The next step would then be to use soap and water once more while scrubbing with both hands until all grime has been removed.
Step Five: Cleaning Your Non-Permanently Mounted Bearings!
For these, you will need a clean rag and some rubbing alcohol (again!) to help dissolve that grime before it has time to accumulate!
Simply take the rag in your hand and use circular motions for this task just like when cleaning off stubborn dirt from corners of your board’s surface or tiny bolts where debris likes to stick around too much. Remember not to scrub the bearing surfaces too hard because they are quite delicate – even with this type of maintenance.
They should last quite a while if used properly thanks to their design which allows them more room between each other than standard bearings found on skateboards (and for longboarders who ride often).
Step Six: Rinsing Your Longboard Off!
Once you are done cleaning your board, it is time to rinse off any excess soap or rubbing alcohol before letting the surface dry. You can do this by wiping with a clean towel and then giving it a good rubdown while checking for any missed stains that need some more attention.
If they still remain after this process, consider using another nylon brush on them – but there should be minimal scrubbing required (especially if you took care of those stubborn spots earlier).
Just make sure not to use too much water because liquid can seep into those tiny cracks in-between bearings which may cause rust over time! It’s always best to let your longboard air out as well so that it can dry.
Step Seven: Keeping your Longboard Clean!
If you want to make sure that it stays in top condition, be sure to keep up with these maintenance tips on a regular basis – especially if you are riding often.
If the board is used infrequently or only for very short-term rides like going across town, then this process may need to be repeated every few months depending on how much time has passed since the last cleaning (or at least check and see if there are any signs of dirt or debris by running fingers over surface before returning).
Brushing off those stubborn corners after each ride will also help prevent grime from accumulating too quickly which means less scrubbing when performing this task! As long as you take good care of it, your board should last for years to come.
Step Eight: Storage!
It is important that you store your longboard in a way that will keep the surface protected from dirt and debris – this means being careful about where it goes when not in use so as to avoid any unwanted scratches or scuffs on its surface while also trying to prevent water damage (or other hazards) which may occur if left out overnight.
You can cover with a cloth or towel after wiping off excess liquid and then place some books under one end so that weight is evenly distributed; alternatively, try wedging something like an old phone book underneath each truck axle area making sure there are no gaps for anything else to enter through.
If possible, consider a place where there will be minimal sunlight exposure and that it is not very humid.
Step Nine: Learning to Maintain Your Board!
One of the most important considerations when learning how to maintain your longboard is ensuring you handle it with care – this means touching only surface areas, staying away from all moving parts or anything else which may cause damage like loose bolts while also avoiding any contact with water (or other liquids) if possible.
If using soap and water for cleaning, take caution by doing so in a well-ventilated area free of dirt and debris because these substances can get trapped inside those tiny cracks between bearings eventually leading to rusting over time!
Also remember that rubbing alcohol needs lots of ventilation as well because fumes are released when it evaporates. If you happen to spill any of these substances on your board, make sure to wipe them up immediately before they dry completely or else the surface will be stained permanently.
Step Ten: Extra Tips!
– For those who want their boards looking super shiny and new, consider applying a coat of carnauba wax every once in awhile which can help maintain that look as well as its natural grip for better control and longer use since it won’t have anything sticking to its surface!
Keep in mind that this process should only take about 30 minutes because too much time may lead to lots of residue build-up which would need scrubbing off later. Be careful not to get water near any part containing metal while drying though because it could cause rusting.
– Some people prefer to use soap and water when cleaning instead of a chemical cleaner because this process is less toxic; however, if you do decide on the latter then make sure it doesn’t contain any abrasive ingredients which can wear down your longboard’s surface over time such as dishwashing detergent or bleach (only mild solutions should be used).
– The best way to prevent friction from occurring between wheels and surfaces for those who don’t want their bearings going bad is by applying wax at least every couple weeks – although some say that doing so too often.
But will eventually lead to dirt built up since there won’t be enough space for all particles during wiping off excess liquid afterward. Wax also helps protect against corrosion so this is another good reason to keep some handy.
– When storing your longboard, make sure it’s in a place where there will be minimal exposure to sun and humidity as these substances can weaken the surface over time (as well as cause damage from any liquids) or else you’ll need more frequent maintenance than usual!
– If you want to remove old wax build up without taking off all that hard work which took months for those new carnauba layers, try using WD40 first by spraying on an area then letting it sit for about 15 minutes before wiping clean with paper towels; if stubborn spots persist afterwards though, use distilled water mixed with vinegar instead. Then apply carnauba wax again – but remember not too often or else it will get dirty too quickly.
Step 11: Buy a good quality longboard!
There are a lot of options when looking for a longboard. It is important to get the best quality board you can afford, while still balancing your budget. As you can see from my story, I learned how to maintain my longboard by reading tutorials and following some really good advice from other professionals in the field as well as by asking questions on forums and getting feedback from others who had gone through it before me.
In the end, I found that making sure everything is cleaned properly and doing basic maintenance on my board has greatly improved the longevity of its use. This includes waxing periodically to prevent rusting or sticking.
Sometimes this isn’t possible though because of where I choose to store my board but I try to keep it out of the sun and store it in a cool, dry place.
To sum everything up, longboards are a fun way to get around and take in the scenery. There’s something about cruising down a hill that makes you feel alive! However, with this great power comes responsibility – it is important to maintain your board by following these steps or else you could be left stranded. If none of them seem like they’ll work for you, don’t hesitate to reach out; our team can provide advice on how best to keep your board clean and well-maintained so it will last many years into the future without any problems!